Fujikura 70S+ Fiber Optik Ek Cihazı
Fujikura 70S+ Fiber Fusion Splicer (Fiber Optik Ek Cihazı)
70S +, otomatik rüzgar koruyucusu / tüp ısıtıcıları gibi bir dizi yenilikçi özelliğe sahip farklı bağlantı ihtiyaçlarını karşılayan yeni standart çekirdek hizalama füzyon splaydır.
6 saniye ekleme ve 9 saniye tüp ısıtma, sağlamlaştırılmış gövde, geliştirilmiş taşıma çantası, kablosuz iletişim fonksiyonları, vb. Hepsi büyük bir ekleme verimliliği için.
| Part No. | FSM-80S | FSM-70S | FSM-60S |
| Applicable fibres | SM (ITU-T G.652 & G.657), MM (ITU-T G.651),DS (ITU-T G.653), NZDS (ITU-T G.655),Others | SM(ITU-T G.652), MM (ITU-T G.651), DS (ITU -T G.653), NZDS (ITU-T G.655) and other single mode fiber including ITU-T G.657 fiber | |
| Fibre Count | Single | Single | |
| Cladding diameter | 80 to 150μm | Cladding Diameter: 80μm to150μm | |
| Coating diameter | 100 to 1000μm | 100 to 1000μm | |
| Actual average splice loss | 0.02dB with SM, 0.01dB with MM, 0.04dB with DS, 0.04dB with NZDS | 0.02dB with SM, 0.01dB with MM, 0.04dB with DS, 0.04dB with NZDS (Measured by cut-back method relevant to ITU-T and IEC standards) | |
| Splice time | 7sec:SM FAST mode, 12sec :SM AUTO mode, 15sec:AUTO mode | Typical 9 sec. with SM FAST, 10sec. with SM AUTO and 13sec with AUTO modes with standard SM (ITU-T G.652) | |
| Return loss | 60dB or greater | 60dB | |
| Splicing modes | 100 splicer modes are available | 100 preset and user programmable modes | |
| Splice loss estimate | Several types of core deformations as well as core axis offset are taken into account for accurate loss estimate | Available | |
| Attenuation splice function | Intentional high splice loss of 0.1dB to 15dB (0.01dB step) can be made for an inline fixed attenuator | Intentional high splice loss of 0.1dB to 15dB (0.1dB step) can be made for an in-line fixed attenuator | |
| Storage of splice result | The last 2000 results to be stored in the internal memory | The last 2000 results to be stored in the internal memory | |
| Magnification | X / Y (300X magnification), or both X and Y simultaneously (160X magnification) | 300X for single X or Y view, or 187X for X and Y view | |
| Viewing method | By two CMOS cameras for intersecting fiber viewing and 4.73 inches TFT colour LCD monitor | Two CMOS cameras and 4.1 inch TFT color LCD monitor | |
| Tension test | 1.96 to 2.25N | 1.96 to 2.25N | |
| Operating condition | 0-5000m above sea level, 0-95% RH and -10 to 50°C respectively | 0 to 5,000m above sea level, 0 to 95%RH and -10 to 50 degC and up to 15m/s wind velocity, respectively | |
| Tube heater | Built-in auto-start tube heater with 10 heating modes and up to 20 for reference | Built-in tube heater with 30 heating modes.Typical 30 seconds with FP-03 sleeve, | |
| Tube heat time | 13-15sec. with FP-03 protection sleeve. Total memory of 30 heating modes are available | ||
| Applicable protection sleeve length | 60mm, 40mm and a series of micro sleeves | 60mm, 40mm and Fujikura FPS01 series. | |
| No. of splice/heating with battery | 200 times of splicing and heat shrinking under with BTR-09 | Typical 160 cycles (splice / tube heat) with BTR-08 | |
| Power supply | Auto voltage selection from 100 to 240Va.c. or 10 to 15Vd.c. with ADC-18. 14.8Vd.c. with BTR-09 | Applicable voltage from 100 to 240V AC or 10 to 15V DC with ADC-13, 13.2V DC with BTR-08 battery | |
| Terminals | USB2.0 ( Mini-B) for data and video signal transfer to PC | USB 1.1 (Mini-B type) connector for PC communication. 6-pin Mini-DIN connector for HJS-02/03 or SH-8 power supply | |
| Dimensions | 146(W) x 159(D) x 150(H) mm | 136W x 161D x 143H (mm) / 5.3W x 6.3D x 5.6H (inches) | |